Engineering Students Drafting Table

ELSHADDAI is one of the primary sources for drafting supplies and drawing equipment

Product Code : ELSHADDAI ARCH - 001

Digital Weather Station with Forecast

Indoor Temperature Range : 32 to 122 degrees Fahrenheit; 0 to 50 degrees Celsius

Temperature Accuracy : +/- 2 degrees Fahrenheit

Product Code : ELSHADDAI ARCH - 003

Solarimeter

Solarmeter UVB Meter For Reptile Lamps - Measures 280-320nm with range from 0-1999 µW/cm² Total UVB

Product Code : ELSHADDAI ARCH - 005

Drawing Instruments Box

ELSHADDAI is one of the primary sources for drafting supplies and drawing instruments

Product Code : ELSHADDAI ARCH - 007

Mini Drafter

 Metal body with steel rad

 Expended size 60cm scale size 15cm x 25 cm

 Fiber material with Zero % error & angle measurement

 Light weight

Product Code : ELSHADDAI ARCH - 009

Beam Test Setup

A bench mounted beam apparatus to allow students to investigate the deflections and reactions in simply supported and cantilevered beams

Product Code : ELSHADDAI AE - 003

Propeller Test Rig

In this test rig, performance of a Propeller can be investigated. The propeller is mounted on a shaft of DC motor. The load cell arrangement is used to measure the thrust force produced by the propeller.

Product Code : ELSHADDAI AE - 005

Flow Visualization Apparatus

The unit uses water as the flow medium. A contrast medium (dye) is injected through small needles into the flow area. Various drag bodies (included) can be placed in the area of flow. In addition, sources and sinks can be simulated and illustrated using eight additional openings in the flow area.

Product Code : ELSHADDAI AE - 006

Apparatus for Verification Of Clarke's Maxwell Theorem

Apparatus consist of a mild steel beam 100cm long and 1.25cm X 4mm in cross section with graduations at every 10cm along the length. It should be supported on two knife edge supports 70cm apart with a 30cm overhang on one side. Reciprocal theorem can be verified by direct measurements of the deflections of various points with the help of a dial gauge due to a load placed at the reciprocal points.

Product Code : ELSHADDAI AM - 001

Curved Member Apparatus

Apparatus consists of a steel bar which is used to make the different curved member Viz. circle, semicircle with straight arm, a quadrant of a circle and quadrant of a circle with straight arm. The bottom ends of the members are fixed to the base. Under the application of load at free end, its horizontal and vertical deflection can be measured with the help of dial gauges.

Product Code : ELSHADDAI AM - 003

Elastic Properties of Deflected Beam Apparatus

Apparatus consists of a mild steel beam 2.5cm X 3mm in cross section and 100cm long, pinned to two supports 70cm apart situated symmetrically. One of the ends can be fixed or given a known slope by applying a known moment at the end with the help of suspended loads. At the other end also a known moment can be applied. Vertical loads can be applied at various points along the span of the beam. A Dial gauge with 25mm travel ( with a magnetic base) may be supplied with the apparatus.

Product Code : ELSHADDAI AM - 005

Portal Frame Apparatus

Apparatus made up of M.S. plate of rectangular section of 3mm thick X 40cm wide. Frame is provided with a provision to achieve different end conditions viz. hinged, roller & fixed. The size of portal will be 40cm X 60 cm. Portal may also have a provision for pulley arrangement and hook arrangement for horizontal loading at different positions. A dial gauge with 25mm travel (with a magnetic base) is supplied with the apparatus. Apparatus will be supplied complete with a supporting stand and a set of weights.

Product Code : ELSHADDAI AM - 007

Unsymmetrical Bending Apparatus

Apparatus consists of a mild steel angle of size 1" X 1" X 1/8" or an equivalent metric units of length 80 cm is tied as a cantilever beam. The beam should be fixed at one end such that the rotation of 45degree intervals are given and clamped such that the principal axis of its cross-section may be inclined at any angle with the horizontal and vertical planes. Also arrangement will be provided to apply vertical load at the free end of the cantilever and to measure horizontal and vertical deflection of the free end.

Product Code : ELSHADDAI AM - 009

Parallelogram Law Of Forces Apparatus

This item is similar to the wall type but is intended for use in laboratories where wall space is limited. At thick plywood piece of thickness 12 mm having substantial metal stand with 2 set of z-pulley and 3 set of ( 50 x 5 gm) slotted weights.

Product Code : ELSHADDAI AM - 011

PRONY BRAKE DYNAMO METER

Consisting of a two blocks of wood clamped together with pulley in the center. The pulley is fitted to shaft moving on the ball bearings. Al lever bar is attached to one of the two blocks carrying a weight hanger at the outer end. A spring balance is also fitted to measure the load factor developed with tightening of the block with wing nut & spring.

Product Code : ELSHADDAI AM - 013

Isothermal Continuously Stirred Tank Reactor

The set up consists of two overhead feed tanks through which two reactants are fed to the reactor. Rotameters are provided to measure the individual flow of Chemicals. The flow rate can be adjusted by operating the needle valves provided on respective Rotameter

Product Code : ELSHADDAI CHE - 001

PLUG FLOW TUBULAR REACTOR

The set up consists of two feed tanks through which two reactants are fed to the reactor. Rotameters are provided to measure the individual flow of Chemicals. The flow rate can be adjusted by operating the needle valves provided on respective Rotameter. The compressed air is used for circulation of feed. A straight tube type reactor kept horizontally and inclined upward at outlet from where samples are collected for analysis. Pressure Regulator, Pressure Gauge and Safety Valve are fitted in the compressed air line

Product Code : ELSHADDAI CHE - 003

Oven

The set-up contains two Jaws of hard steel with one Jaw stationary and other moving. The movable jaw produces blows for every revolution reducing over sizing to a minimum. A combination of forward and downward strokes with a rocking action exert pressure on the coarser materials yet permits the finished materials to pass through the jaws. A hopper is provided at the top for feeding material. The smooth jaws ensure a uniform product and easy cleaning is possible

Product Code : ELSHADDAI CHE - 010

Digital Spectrophoto meter

Lab setup is used to crush different sample and material. Two heavy smooth faced chilled metal rolls turning on parallel horizontal axes are the working elements of the roll crusher. A hopper is provided at the top for feeding the material. Particles of feed caught between the rolls are broken in compression and drop out below. The rolls turn towards each other at the same speed.

Product Code : ELSHADDAI CHE - 012

Auto Karl Fischer Titrimeter

Lab setup is used to crush different sample and material. Two heavy smooth faced chilled metal rolls turning on parallel horizontal axes are the working elements of the roll crusher. A hopper is provided at the top for feeding the material. Particles of feed caught between the rolls are broken in compression and drop out below. The rolls turn towards each other at the same speed.

Product Code : ELSHADDAI CHE - 014

CUBE MOULDS

Made of cast iron conforming to the specifications and tolerance in accordance to I.S.-516 and latest I.S.-10074 SIZE- 150 X 150X150MM.

Product Code : ELSHADDAI CVL - 001

PRISM MOULD

One gang prism mould to produce 25x25x250 mm specimens for expansion tests in autoclave. Complete with 4 steel inserts.

Product Code : ELSHADDAI CVL - 003

CONCRETE MIXER

Laboratory model capacity 2.5 cft mounted on rubber tiers and sturdy frame with towing rod. ELECTRICALLY OPERATED.

Product Code : ELSHADDAI CVL - 005

FLOW TABLE

Conforming to the specification and tolerance in accordance to I.S.-1199. Designed for the determination of the flow of the Portland cement concrete. The tabletop is 76.2cms. Diam finally machined from a solid casting the integral cast ribs are also designed for support and strength. The stand is fabricated out of cast iron and is on sturdy construction. Holes for mounting on foundation are drilled in the base plate. The ground and polished steel cam is designed to drop 12.5mm. Manually operated unit

Product Code : ELSHADDAI CVL - 007

VEE-BEE CONSISTOMETER

Conforming to the specifications and tolerance in accordance to I.S.-1199 used for the determination of the workability of the concrete. The concrete is deform in a container and is vibrated after removing the cone on a small vibrating table operated at a fixed amplitude and frequency operation 220 Volts single phase A.C.supply

Product Code : ELSHADDAI CVL - 009

LABORATORY C.B.R. APPARATUS (HAND OPERATED)

Conforming to the specifications and tolerance in accordance to I.S.-2720, Part-XVI used for the determination of the laboratory C.B.R. consists of : - 01.) Load Frame Hand operated capacity 50 KN (5000 kgs.) with high and low rate of travel of the lead screw. 02.).C.B.R. Mould:-Conforming to the specifications and tolerance in accordance to I.S.-9669-1980 made of chromium steel 150mm.

Product Code : ELSHADDAI CVL - 011

TROWELS AND PLANERS

Conforming to the specifications and tolerance in accordance to I.S.-2720, Part-XVI used for the determination of the laboratory C.B.R. consists of : - 01.) Load Frame Hand operated capacity 50 KN (5000 kgs.) with high and low rate of travel of the lead screw. 02.).C.B.R. Mould:-Conforming to the specifications and tolerance in accordance to I.S.-9669-1980 made of chromium steel 150mm.

Product Code : ELSHADDAI CVL - 013

MARSHALL STABILITY APPARATUS

The test is applicable to hot mix designs using bitumen and aggregates upto a maximum size of 25mm. In this method, the resistance to plastic deformation of cylindrical specimen of bitumenous mixture is measured when the same is loaded at periphery at 5 cm per min. This test procedure is used in designing and evaluating bitumenous paving mixes.

Product Code : ELSHADDAI CVL - 015

DORRY ABRASION TESTING MACHINE

Owing to our years of experience and knowledge of this domain, we have been able to manufacture, supply, export and trade finest quality Dorry Abrasion Testing Machine. We have manufactured the offered range of abrasion testing machines using high grade raw material and components that are obtained from the most trusted and reputed vendors of the market. Offered Dorry Abrasion Testing Machine is generally used to test the coarse aggregate abrasion resistance.

Product Code : ELSHADDAI CVL - 017

two stroke diesel engine

This working cut section model designed to enable students to study different systems of an automobile petrol and diesel engine & demonstrate its working. The setup uses an actual automobile petrol and diesel engine, sectioned at suitable locations to display internal assembles.

Product Code : ELSHADDAI CSW - 001

four stroke petrol engine

This working cut section model designed to enable students to study different systems of an automobile petrol and diesel engine & demonstrate its working. The setup uses an actual automobile petrol and diesel engine, sectioned at suitable locations to display internal assembles.

Product Code : ELSHADDAI CSW - 003

Model of Cut Sectioned Petrol MPFI Engine Assembly

This cutaway model is carefully sectioned for training purposes, professionally painted with different colours to better differentiate the various parts, cross-sections, lubricating circuits, fuel system, cooling system etc.

Product Code : ELSHADDAI CSW - 005

Engine Parts cut section

This cutaway model is carefully sectioned for training purposes, professionally painted with different colours to better differentiate the various parts, cross-sections, lubricating circuits, fuel system, cooling system etc.

Product Code : ELSHADDAI CSW - 007

Cut section of the brake Assembly

This cutaway model is carefully sectioned for training purposes, professionally painted with different colours to better differentiate the various parts, cross-sections, lubricating circuits, fuel system, cooling system etc.

Product Code : ELSHADDAI CSW - 009

CNC TURN TRAINER

 Table size : 400*150mm

 Tool Dia : 5/6/8mm

 Accuracy : 0.01mm

 Weight : 350 kgs

Product Code : ELSHADDAI CNC - 001

CAM ANALYSER

The apparatus is designed to study the cam profiles and performance of cam and follower system. A shaft supported by ball bearings upon which three different types of cams can be mounted.

Product Code : ELSHADDAI DYN - 001

GOVERNOR

To study the determination of characteristics curves of radius of rotation against controlling force (Actual & Theoretical) for all governors. The set-up is designed to study the working of different governors normally used to control the speed. It consists of a main spindle, mounted vertically on the base plate.

Product Code : ELSHADDAI DYN - 003

STATIC AND DYNAMIC BALANCING MACHINE

This equipment is designed for carrying out the experiment for balancing a rotation mass system. The apparatus consists of four circular discs mounted on a shaft. The discs are grooved for the attachment of weights at a specific radius. The block are clamped on shaft is rotated by a motor to check dynamic balance of the system.

Product Code : ELSHADDAI DYN - 005

VIBRATION TEST FACILITIES APPARATUS

The apparatus is designed to help in conducting various experiments to illustrate and verify the principles and relations involved in the study of vibrations. Following experiments can be performed with this unit.

Product Code : ELSHADDAI DYN - 007

DYNAMIC BALANCING MACHINE

Weight : 2-10kg,
Max. Distance Between Bearing: 500mm,
Balancing Speed Range (N)600-3000rpm,
Shaft Diameter5-50mm,
Power Of Drive Motor 0.33hp ,
Acceleration Capacity Gd2 N20.40x106 Kgm2n2,
Max. Unbalance Mass Read At 100% Of Meter Scale:30gm

Product Code : ELSHADDAI DYN - 009

JOURNAL BEARING APPARATUS

EEE Journal Bearing apparatus for investigating the distribution of pressure in slide bearings illustrates the principle of hydrodynamic lubrication. The distribution of pressure and the carrying capacity can be determined on a sliding bearing model at different bearing loads and speeds. The sliding bearing consists of a bearing journal driven by an electrical motor and the freely moving bearing housing. The bearing is loaded with different, interchangeable weights. The setup contains manometer tubes, dc motor, dc drive to control speed, set of weights, oil tank, Journal bearing along with the shaft.

Product Code : ELSHADDAI DYN - 011

BEVEL GEAR

Either of a pair of gears with teeth surfaces cut so that they can connect unparallel gear shafts. (Mechanical Engineering) a gear having teeth cut into a conical surface known as the pitch zone. Two such gears mesh together totransmit power between two shafts at an angle to each other

Product Code : ELSHADDAI DYN - 013

DIFFERENTIAL GEAR

An arrangement of gears in an epicyclic train permitting the rotation of two shafts at different speeds, used on the rear axle ofautomotive vehicles to allow different rates of wheel rotation on curves. An arrangement of gears in an epicyclic train permitting the rotation of two shafts at different speeds, used on the rear axle ofautomotive vehicles to allow different rates of wheel rotation on curves.

Product Code : ELSHADDAI DYN - 015

COMPOUND GEAR TRAIN

Compound gear trains involve several pairs of meshing gears. They are used where large speed changes are required or to get different outputs moving at different speed

Product Code : ELSHADDAI DYN - 017

Epicycle gear Train Apparatus

Gear Train is any combination of gear wheels by which motion is transmitted from one shaft to another shaft. In epicyclic gear trains, the axes of shafts on which the gears are mounted may move relative to a fixed axis.

Product Code : ELSHADDAI DYN - 019

ROPE BRAKE DYNAMOMETER

 230 V Single Phase
 Rope Brake Drum Assembly
 Digital R.P.M. Indicator
 Energy meter, Voltmeter, Ammeter to measure input power of motor

Product Code : ELSHADDAI DYN - 022

Slip & Creep Measurement Apparatus in Belt Drive

This apparatus is useful for measurement of power transmitted for various input power conditions with varied belt tension. Belt slip or creep also can be measured. The apparatus consists of a variable speed D.C. Motor, driving pulley and driven pulley of equal diameters. The pulleys are mounted on input shaft (motor shaft) and output shaft. The driven pulley can slide on the base only with bearing block to change the initial tension in belt

Product Code : ELSHADDAI DYN - 024

Drill Tool Dynamometer

Elshaddai’s Tool dynamometers to measure cutting forces on various machines like lathe, drill, milling machines. All three direction forces are measured simultaneously and displayed

Product Code : ELSHADDAI DYN - 026

Spring Mass System

The apparatus is designed to help in conducting various experiments to illustrate and verify the principles and relations involved in the study of vibrations. Following experiments can be performed with this unit.

Product Code : ELSHADDAI DYN - 028

Transverse Vibration Setup

The apparatus is designed to help in conducting various experiments to illustrate and verify the principles and relations involved in the study of vibrations. Following experiments can be performed with this unit.

Product Code : ELSHADDAI DYN - 030

Friction and were test rig

It is essential to decide the wear rate at design stage, in doing so it is necessary to develop such an equipment which will serve the purpose of material testing. The purpose of friction and wear test

Product Code : ELSHADDAI DYN - 032

Transverse Vibration Set Up

Frame Size:1200X450

2 channel 500mm length

Scale fitting movable

Product Code : ELSHADDAI DYN - 034

Single and Two Rotor System

To determine the natural frequency of undamped torsional vibration of a single rotor shaft system. When the particles of the shaft or disc move in a circle about the axis of the shaft, then the vibrations are known as torsional vibrations. The shaft is twisted and untwisted alternatively and the torsional shear stresses are induced in the shaft.

Product Code : ELSHADDAI DYN - 036

Dynamic Balancing Of Reciprocating Masses

Dimension 300 x 250 x 400 mm the entire system is mounted on a heavy duty frame which is embedded with multi springs to absorb the shock generated while reciprocation is in action with reciprocating system duly fixed on the frame and driven through dc motor with variable rpm level and duly indicated through the digital rpm monitor.

Product Code : ELSHADDAI DYN - 038

Forced vibration analysis (Spring Mass System Motorised)

A system is said to be a cantilever beam system if one end of the system is rigidly fixed to a support and the other end is free to move. Few Examples of Real life systems which can be approximated to Cantilever Beam are shown. Single degree of freedom mass spring damper system under free vibration is governed by the following differential equation

Product Code : ELSHADDAI DYN - 038

DIGITAL PH METER (LAB MODEL)

Led Display 31/2 digits 0 to 14 PH, 0 to ±2000 mv.

Accuracy ±0.01 ph, 1 mv,±1 digit. Resolution 0.001

Indicator, temp. Compensation 0 to 100°C (Manual)

Power supply 230V ± 10% Hz supplied with combine

Electrode, buffer solution Electrode stand, dustcover.

Product Code : ELSHADDAI CVL - 018

AUTO DIGITAL CONDUCTIVITY METER

 Display : 16 x 2 alpha numeric, LCD display

 Range : 0.1 uS to 100mS (6 decadic ranges)

 Resolution : 0.1 • Accuracy+ 1% of F.S. + 1 digit

 Calibration : Auto / Manual

Product Code : ELSHADDAI CVL - 020

TURBIDITY METER

 Display : 3.5 Digit LED.

 Power : 230V ± 10% 50 Hz.

 Range : 0 to 1000 NTU in 2 ranges.

 Resolution : 1 NTU.

Product Code : ELSHADDAI CVL - 022

DIGITAL COLONY COUNTER

 Display : 4 Digit LED.

 Packaging : 23cm x 28cm x 20cm Corrugated carton

 Power : : 230V - 10% AC,50 Hz 40w

 Accessories : Marking Pen - 1 No. Magnifier Lens - 1 No

Product Code : ELSHADDAI CVL - 024

AUTOCLAVE

Construction : Single walled construction, the wall is made of thick high grade stainless steel sheet of SS - 304 grade. The lid is made of stainless steel sheet. Provided with built in safety valve, pressure gauge, pressure release valve.

Product Code : ELSHADDAI CVL - 026

ROTATIONAL Viscometer

A continuous sensing capability for rapid viscosity measurement makes this economical digital viscometer a standout. Measures viscosity and temperature simultaneously (with an optional temperature probe). With its timed measurement function, data can easily be sent to a PC or printer. Optional software allows the DV-I Prime to collect, analyze and record test data.

Product Code : ELSHADDAI FTL - 001

Saybolt Viscometer For Testing Lab

The apparatus consists of stainless steel bath and universal and furol jets of stainless steel stirring is done manually with turn table arrangement.

Product Code : ELSHADDAI FTL - 003

Flash Point Cleveland For Testing Lab

This apparatus is used for determination of flash and fire pt. of petroleum products except fuel oils and those having an open cup flash below 790C. The apparatus consists of a cup, heating plate specific dimensions, thermometer clip and test flame attachment with service 1 joints for passing over test liquids surface in the prescribed manner. Heating is controlled by means of energy regulator fitted to apparatus Suitable for operation on 220 V. AC.

Product Code : ELSHADDAI FTL - 005

Drop Point Apparatus For Testing Lab

This is used for determining drop point of greases as per IP 31,132 & ASTM-D-566. It is an indication of the critical temperature of the solid or semi solid to the liquid state. The apparatus consists of brass sleeve and case with metal cup and a glass boiling tube with cork fitted to a bath (Beaker) is provided. A FHP Motorized stirrer and electrical heater with energy regulator control is also provided.

Product Code : ELSHADDAI FTL - 007

Tar Viscometer For Testing Lab

Tar viscometer apparatus as per IP-72 and IS 1206 standards. It is used for determination the viscosity of road oils and cut back bitumen. It consists s. S. Bath with cup of 10 mm or 4 mm orifice and sleeve, stirrer with lifting clip and ball. The assembly kept on suitable stand with leveling screws. Suitable to operate on 220 volts ac mains.

Product Code : ELSHADDAI FTL - 009

Reid Vapour Pressure Test Apparatus For Testing Lab

As per IP 212 and ASTMD-490. Used for determining the Viscosity of lubricating and fuel oils.

Product Code : ELSHADDAI FTL - 011

Bomb Calorimeter Apparatus For Testing Lab

Bomb Calorimeter with DIGITAL Temp. Indicator Stainless Steel jacket vessel with electronic timer & firing unit

Product Code : ELSHADDAI FTL - 013

Softening Point Apparatus Ring & Ball Apparatus For Testing Lab

Conforming to the specifications and tolerance in accordance to I.S.-1205 used for the determination of the temperature at which a sample of bitumanious material loaded by a 9.5mm. steel ball drops a specified distance when heated under specified conditions. Comprise a water bath of heat resistance glass, two tapered rings, two Ball Centering guide, two steel balls of 9.5mm dia and a ring holder.

Product Code : ELSHADDAI FTL - 015

Aniline Point Apparatus

Product Code : ELSHADDAI FTL - 017

GUARDED PLATE APPARATUS

To determine the thermal conductivity of liquids by guarded hot plate. The apparatus consists of a main heater and a radial guard heater sandwiched between copper plates. The specimen in the form of slabs of equal thickness are placed on either sides of heaters and cooling plates through which water is circulated are on the other sides of the specimen. The radial guard heater ensures all heat of the main heater to pass axially through the specimens which is collected by cooling plates

Product Code : ELSHADDAI HTL - 001

NATURAL CONVECTION-VERTICAL CYLINDER APPARATUS

It is designed to study the temperature distribution along the length of a vertical pipe in natural convection. The unit consists of a vertical brass pipe heated by a cartridge heater inside it. It is fitted in an enclosure to provide undisturbed natural convection currents. Thermocouples are attached on the pipe to measure local temperatures. Heater input is measured on voltmeter and ammeter.

Product Code : ELSHADDAI HTL - 003

PIN - FIN APPARATUS

The apparatus is designed to calculate the heat transfer rate from the fin and the fin effectiveness in natural & forced convection. The apparatus consist of a pin type fin heated by a band heater at one end. It consists of a channel in which the pin fin is tested in both natural as well as forced convection. A centrifugal blower draws air over the fin. The blower is operated to touch the pin fin in forced convection only Thermocouples are attached along the length of fin to note down the longitudinal temperature gradient.

Product Code : ELSHADDAI HTL - 005

REFRIGERATION TEST RIG

To determine the COP of given plant. The apparatus consists of compressor, condenser, dryer, digital temperature indicator, sensor, pressure gauge & vacuum gauge. Eco-friendly R 134A is used as refrigerants in our Air Conditioning Test Rig. Our Air Conditioning Test Rig is highly useful in conducting experiments on a vapor compression air conditioning unit.

Product Code : ELSHADDAI HTL - 007

AIR COMPRESSOR TEST RIG

To study the Volumetric Efficiency of Compressor. Both Single stage compressor and Two stage compressor can be used. The setup consists of 6 channel digital temperature indicator with an energy meter and U Tube Manometer.

Product Code : ELSHADDAI HTL - 009

Composite wall apparatus

To study the Volumetric Efficiency of Compressor. Both Single stage compressor and Two stage compressor can be used. The setup consists of 6 channel digital temperature indicator with an energy meter and U Tube Manometer.

Product Code : ELSHADDAI HTL - 011

open drum orifice

Main supply tank with orifice & mouthpiece fitting arrangement.

Diameter of Orifice-8.5mm,Diameter of mouthpiece-8.5mm.,Nozzle-25mm.&50mm length.

Tracer pointer with scale.

Measuring tank

Product Code : ELSHADDAI HYD - 001

Notch apparatus

Types of notch : 600 v notch , rectangular notch, Trapezoidal.

Flow channel : 250 x 250x 1250 mm with notches fitting arrangement

Pipes and Valves : 1” G.I. piping and 1” Brass valves.

Water storage Unit : Sump Tank – 900 x 400 x 400 mm M.S. tank with F.R.P. coating. Or S.S. tank.

Product Code : ELSHADDAI HYD - 003

Bernoulis theorem

Flow channel : 750mm long with transparent solid acryalic

Pipes and Valves : 1” G.I. piping and 1” Brass valves

Water storage Unit : Sump Tank – 900 x 400 x 400 mm M.S. tank with F.R.P. coating. Or S.S. tank.

Product Code : ELSHADDAI HYD - 005

Kaplan Turbine Test Rig:

Kaplan wheel turbine is an axial flow reaction tubine named in honour named in honour of Sir L Dr. B. Kaplan, a German Engineer.This tubine suitable low head. The power produced by a proportional to QH. Asa head (H) Decrease the discharge (Q) must increase to produce the same power.

Product Code : ELSHADDAI HYD - 007

parallel and series pump experiment setup

In complex systems, pumps can be connected in series or in parallel. In serial operation the heads of the pumps are added and in parallel operation the flow rates (capacities) of the pumps are added.

Product Code : ELSHADDAI HYD - 009

Hydraulic Flume Apparatus

A hydraulic flume of c/s 200x300 mm & 6000 mm length with transparent window on either sides of 1000 mm length.

Sliding gates one at upstream and other at the downstream side.

Screw jack for change of the slope of the flume.

A Sump tank of sufficient capacity.

Product Code : ELSHADDAI HYD - 011

ENGINE CUT SECTION MODELS

Two Stroke Cut Section Model : Single cylinder 2 stroke petrol engine for plotting port timing diagram

Four Stroke Cut Section Model : Single cylinder 4 stroke diesel engine for plotting valve timing diagram

Product Code : ELSHADDAI THR - 001

Variable compression ratio diesel engine test rig

The setup consists of single cylinder, four stroke, VCR (Variable Compression Ratio) Diesel engine connected to eddy current type dynamometer for loading. The compression ratio can be changed without stopping the engine and without altering the combustion chamber

Product Code : ELSHADDAI THR - 003

DIESEL ENGINE TEST RIG

 Performance Test

 Heat Balance Test

Engine: 5 HP at 1500 RPM coupled with loading device on a common base plate.

Product Code : ELSHADDAI THR - 005

SINGLE CYLINDER 4 STROKE AIR COOLED PETROL ENGINE TEST RIG

To carry out the following experiments

Different Types of Loading:

 Performance Test  Rope Brake Dynamometer  Electrical Dynamometer

Product Code : ELSHADDAI THR - 007

EXHAUST GAS ANALYSER

This product is used in various industry like automobile, petrochemical and food industry for analyzing exhaust gas from the fuel.

Product Code : ELSHADDAI THR - 009

Steam Boiler With Turbine Set

 Fire Tube

 Capacity : 300 Kgs/Hr

 Max.Pressure: 6 Bar

 Working Pressure: 3 Bar

Product Code : ELSHADDAI THR - 011

Lathe Machine

 Hight of centre : 165mm

 Swing over slide : 190mm

 swing over bed : 315mm

 swing in gap : 500mm

Product Code : ELSHADDAI MT - 001

CAPSTAN LATHES

 Maximum bar Capacity Round : 25 mm

 Square : 18 mm

 Maximum Capstan Stroke mm : 50

 Operated with Hydralic System : 100 mm

Product Code : ELSHADDAI MT - 003

Vertical Universal Milling Machine

 Face of Body : 9"

 Surface of Table : 42" x 9"

 No of Tee-Slots : 3

 Size of Tee-Slots : ½"

Product Code : ELSHADDAI MT - 005

Cylindrical Grinding Machine

 General Height of center : 125 mm

 Distance between center : 300mm.

 Maximum swivel : Degree-7+3

 Speed approach : 300/3000 mm/min

Product Code : ELSHADDAI MT - 007

RADIAL DRILL MACHINE 25 MM

 Machine Capacity : 25 / 650

 Drilling ( M.S ) : 25

 Hight of base plate : 125

 Working Surface : 500 x 710

Product Code : ELSHADDAI MT - 009

Slotting Machine

 Stroke : 10 mm to 150 mm

 Longitudinal Movement : 200 mm

 Cross Movement : 110 mm

 Speed Adjustment : 3 Speed

Product Code : ELSHADDAI MT - 011

ABSORPTION IN PACKED BED

The set up consists of a glass column packed with Rasching rings. Liquid is fed at the top of the column through distributor. The solute gas and air are measured separately, mixed in a mixing chamber and then passed through the packed column vertically upward and absorbed in liquid. All the flow rates can be independently varied to simulate different conditions.

Product Code : ELSHADDAI CHE - 016

LIQUID-LIQUID EXTRACTION IN A PACKED TOWER

The set-up consists of a glass column packed with Rasching rings. Continuous counter current contacts between the solvent and solute phases are made, which results into extract and raffinate streams. Flow meters (Rotameters) are used to note the flow of solvent & solute respectively.

Product Code : ELSHADDAI CHE - 018

FORCED DRAFT TRAY DRYER

The set-up consists of an insulated double wall chamber. Inside the chamber a tray is attached directly to a electronic weighing balance, which is fitted on the bottom, outside the chamber. Material for drying is placed in the tray and regular loss of weight is monitored. Air from a blower passes through a heating chamber and is used as drying agent.

Product Code : ELSHADDAI CHE - 020

Steam Distillation

Steam distillation is used industrially to purify liquids, which are immiscible with water, and to remove bad odors from oils. When water is added to a high boiling liquid immiscible with it, the total pressure exerted by the mixture above the liquid surface will be the sum of the vapor pressures of the pure components and therefore the boiling point of the mixture will be less than that of water at the given temperature.

Product Code : ELSHADDAI CHE - 022

Jaw Crusher

The set-up contains two Jaws of hard steel with one Jaw stationary and other moving. The movable jaw produces blows for every revolution reducing over sizing to a minimum. A combination of forward and downward strokes with a rocking action exert pressure on the coarser materials yet permits the finished materials to pass through the jaws. A hopper is provided at the top for feeding material. The smooth jaws ensure a uniform product and easy cleaning is possible

Product Code : ELSHADDAI MECH - 001

ROLL CRUSHER

Lab setup is used to crush different sample and material. Two heavy smooth faced chilled metal rolls turning on parallel horizontal axes are the working elements of the roll crusher. A hopper is provided at the top for feeding the material. Particles of feed caught between the rolls are broken in compression and drop out below. The rolls turn towards each other at the same speed.

Product Code : ELSHADDAI MECH - 003

ELECTRO PNEUMATIC TRAINER KIT

 Power Supply: AC 220 V

 Power Consumption: ≤0.3 kVA

 Dimensions: 500 mm x 300 mm x 140 mm

Product Code : ELSHADDAI MECH - 001

Mechatronics Lab Equipments

With our expertise in this domain, we are able to offer a superior quality range of Mechatronics Lab Equipments. Our team members design these product range keeping in mind the specifications and requirements of our customers. Moreover, the product offered by us are available in the demanded specification, which help in meeting the variegated demands of our customers in an efficient manner.

Product Code : ELSHADDAI MECH - 003

Traffic Light Control Unit

Simulation of Traffic Signal Control using PLC Extension module for use with PLC Training Rack

Product Code : ELSHADDAI MECH - 005

Robotic Arm Control Trainer

We are involved in delivering a wide series of Robotic Arm Control Trainer.

Product Code : ELSHADDAI MECH - 007

Program Logic Controller

PLC 301 is a Microcontroller based Programmable Logic Controller which replaces conventional hard wired relay circuits, Timers, Counters etc. The simple and flexible ladder logic programming using a PLC ensures easy process modification compared to an equivalent hard wired system.

Product Code : ELSHADDAI MECH - 009

Basic Hydraulic Trainer Kit

we have brought forth a huge variety of Electro Hydraulics Trainer Kit.

Perfect finish

Industry proven designs

Longer life

Product Code : ELSHADDAI MECH - 011

Disc Polishing Machine

 Motor Disc Size : 8”

 Dimension lxbxh : 725 x 525 x 425

 Drive Capacity : 0.5/AC Motor

 Drive : Pulley and belt drive

Product Code : ELSHADDAI MET - 001

Jominy End Quench Test Apparatus

This apparatus is useful for determining the harden ability of steels by end quench test. The test consists of heating a standard size specimen to a given temperature for a specific period of time, followed by a water quenching of one end under specified conditions and measuring the hardness at various points from quenched end along the length of test piece.

Product Code : ELSHADDAI MET - 003

Mounted Specimen Sets Manufacturers

This set consists of different Metallurgical Structure specimen. Fully polished, prepared and etched

Product Code : ELSHADDAI MET - 005

Specimen Cutting Machine

 Maximum Sample Selection : 30 X 30mm

 Grinding Wheel Size : 300 X 2 X 32mm

 Rotate Speed : 1500 rpm/mion. apprx.

 Dimensions : 24 X 26 X 30 Inches

Product Code : ELSHADDAI MET - 007

Metallurgical Microscope

It is used for inspecting, identifying, measuring microscopic metal grain structures.Metallurgical microscope is the optical microscope, differing from other microscopes in the method of the specimen illumination.

Product Code : ELSHADDAI MET - 007

Furnace

 Electrical Muffle Furnace with inner

 Dimension 150X150X300mm maximum

 Temperature 1100 Deg C, with digital

 Controller and Cr/Al Thermocouple 3.5 KW

Product Code : ELSHADDAI MET - 009

FLOATING CARRIAGE MICROMETER

Specification : This measuring machine is designed to have accurate measurements of major,minor & effecive diameter of precision screw threads as well as those of odd flutes screw taps. All guide ways and wearing parts are hardened and ground

Work piece :16.20mm | Prism :2 nos | Method : Two wire method

Product Code : ELSHADDAI MTR - 001

DISPLACEMENT MEASURING SETUP

 Specification : ±10mm

 Micrometer : ±0-25mm

 Indicator : Digit to read upto 10mm

Product Code : ELSHADDAI MTR - 003

FORCE VIBRATION TESTING

Load cell : 1kg capacity

weight : 100gms. x 10 nos

Indicator : 3½ digit display to read upto 1 kg

Resolution : 0.01 kg

Product Code : ELSHADDAI MTR - 005

BEVEL PROTECTOR

Specification : Range - 360 Deg, LC:5Min, it is capable of measuring from 0 to 360°. the vernier scale has 24 divisions coinciding with 23 main scale divisions. thus the least cout of the instrument is 5.This instrument is most commonly used in workshops for angular measurments till more precision is required

Product Code : ELSHADDAI MTR - 007

ELECTRICAL COMPARATOR

Specification : Operates on the principal of the Change of inductance of a coil by movement of a steel armature,which is moved by a plunger arrangement in contact with the surface to be checked. the plunger consists of Electrical Gauge Head with armature and feeler,Ammeter,Power Supply,with 2 amps x 2 Nos. dimmer & specimen Holder

Product Code : ELSHADDAI MTR - 009

TOOL MAKER'S MICROSCOPE

Specification : Magnification:30 X with X-Y movement on ball bearingcslides

Micrometer:(50mm dia)L.C 0.01 with monometer Having both Transmitted and incident light in wooden box.

Product Code : ELSHADDAI MTR - 011

SINE CENTER

Specification : Range 100, 150mm, 208mm, 250mm & 300mm. for the inspection angle checking and taper checking

Product Code : ELSHADDAI MTR - 013

DIAL GAUGE

Specification : 0-10 mm 0.01 LC with magnetic base stand

Product Code : ELSHADDAI MTR - 015

MICROMETER

Specification : Measuring range of 25-32mm, 25-50mm, 50-63mm, 50-200mm, 50-300mm, 200-225mm, 200-500mm, 200-1000mm.

Product Code : ELSHADDAI MTR - 017

VERNIER HEIGHT GAUGE

Specification : Measuring range of 300/12", 450mm/18", 600mm/24", 1000mm/40".

Product Code : ELSHADDAI MTR - 019

Coordinate Measuring Machine

Measuring Range : 200x200x200mm

Linear Accuracy U1 : 3+L/200µm

Maximum Weight : 60Kgs

Maximum Part Weight : 200mm

Product Code : ELSHADDAI MTR - 021

Telescopic Gauge

Range : (8 - 150mm) (6 Gauge Set)

(Set Content: 812.7mm, 12.719mm, 1932mm, 3254mm, 5490mm& 0150mm)

Product Code : ELSHADDAI MTR - 023

MEASURING INSTRUMENTS

Range : (8 - 150mm) (6 Gauge Set)

(Set Content: 812.7mm, 12.719mm, 1932mm, 3254mm, 5490mm& 0150mm)

Product Code : ELSHADDAI MTR - 023

MICHELSON INTERFEROMETER

The Michelson interferometer is a common configuration for optical interferometry using a beam splitter, a light source is split into two arms. Each of those light beams is reflected back toward the beam splitter which then combines their amplitudes using the superposition principle

The Michelson Interferometer is a superb instrument for measuring the optical properties of a medium.
E.g. refractive index, phase shifts, visualization of interference

Specifications:-

Michelson Interferometer based on Model developed by Hilger & Watts (London)It is divided into two parts.

(1) Mechanical
(2) Optical Mechanical part consists of following items
a) Bed: Bed is optically ground, Length 250mm
b) Lead Screw: Lead screw is optically ground with its nut, length 200 mm Pitch 1 mm
c) Optical Mirror Mount: Kinematic mirror mounts are to hold the mirror which be aligned in to orthogonal direction by means of screws provided at the rare of the mount.

Optical Parts consist of the following items:
a) Beam Splitter
b) Compensating plate Size 45mm× 32mm × 8mm 50mm× 35mm × 8mm Beam splitter and compensating plates are covered from the same optically worked glass plate

Surface flatness : λ/10 (both faces)
Parallelism : 5 arc sec.
Mirrors : 2Nos.
Focal Length : 25mm thickness 10mm
Front surface : Coating material : Coated AI with SiO2
L.C. of Instrument :10¯4mm

Product Code : ELSHADDAI MTR - 025

PRESSURE DROP THROUGH PACKED BED

We offer high quality Michell Tilting Pad Bearing Apparatus to our esteemed customers. The offered apparatus is commonly used for the purpose of demonstrating the pressure distribution that occurs in pad bearing. Owing to easy the installation and flawless design, this offered apparatus is highly demanded in the market.

Product Code : ELSHADDAI MTL - 001

FLOW THROUGH HELICAL COIL

Helical coils are used for heating or cooling in process tanks. When a fluid flows through a curved tube, centrifugal force acting upon the various elements of fluid moving with different velocities causes secondary circulation. Secondary flow results in higher heat transfer characteristics. Further, secondary flow stabilizes the laminar flow leading to a higher critical Reynolds number for transition from laminar to turbulent flow.

Product Code : ELSHADDAI MTL - 003

PRESSURE DROP IN TWO PHASE FLOW

 Water Circulation FHP Pump, Crompton / Sharp make

 Flow Measurement Rotameters. 2 Nos. (one each for Water & Air).

 Air Circulation By Compressed Air

 Water Tank Material Stainless Steel/PVC, Capacity 60 Ltrs

Product Code : ELSHADDAI MTL - 005

NON Destructive Testing Equipment (NDT)

NDT Equipment comprises an assortment of analysis techniques that are used in science and industry for evaluating properties of component/system and material without causing any damage. The involved process also known by the common names of Nondestructive inspection (NDI), Nondestructive examination (NDE), Nondestructive evaluation (NDE) has indeed come up as a highly sought after technique that helps in saving both money and time in processes involving product evaluation, troubleshooting and research

Product Code : ELSHADDAI NDT - 001

Dye Penetrant Testing Equipment

 Packaging Size : 400 ML

 Packaging Type : 400 ml

 Penetrant, Developer and Cleaner

Product Code : ELSHADDAI NDT - 001

Digital Lux Meter

 Range : 200 to 2, 00, 000 lux

Product Code : ELSHADDAI NDT - 001

NDT Equipments & Consumabales

Flaw Check Liquid Penetrant products, Magnetic Crack Detector, Magnetic yoke crack detector, Ultra sonic Flaw Detector, Ultrasonic cleaner

Product Code : ELSHADDAI NDT - 001

FIRST AND SECOND ORDER SYSTEM

This unit consist „U‟ Tube manometer, Stop watch, Heat source, Controller etc., to study the First order and second order system

Product Code : ELSHADDAI CHE - 005

LEVEL PROCESS CONTROL SYSTEM

It consists of one Level sensor, water pump, Process tank with plumbing & hand Valves, etc.,

Product Code : ELSHADDAI CHE - 007

TEMPERATURE AND THERMAL PROCESS CONTROLLER

Temperature Process Control Trainer is one of the most advanced industrial prototypes learning equipment. It consists of one Temperature Sensor, Power driver circuit, Water Heater with Plumbing & Hand Valve

Product Code : ELSHADDAI CHE - 009

RESPONSE OF THE SECOND ORDER SYSTEM

To Study the response of Second order system

Product Code : ELSHADDAI CHE - 011

Isothermal Continuously Stirred Tank Reactor

The set up consists of two overhead feed tanks through which two reactants are fed to the reactor. Rotameters are provided to measure the individual flow of Chemicals. The flow rate can be adjusted by operating the needle valves provided on respective Rotameter

Product Code : ELSHADDAI CHE - 001

PLUG FLOW TUBULAR REACTOR

The set up consists of two feed tanks through which two reactants are fed to the reactor. Rotameters are provided to measure the individual flow of Chemicals. The flow rate can be adjusted by operating the needle valves provided on respective Rotameter. The compressed air is used for circulation of feed. A straight tube type reactor kept horizontally and inclined upward at outlet from where samples are collected for analysis. Pressure Regulator, Pressure Gauge and Safety Valve are fitted in the compressed air line

Product Code : ELSHADDAI CHE - 003

ABSORPTION IN PACKED BED

The set up consists of a glass column packed with Rasching rings. Liquid is fed at the top of the column through distributor. The solute gas and air are measured separately, mixed in a mixing chamber and then passed through the packed column vertically upward and absorbed in liquid. All the flow rates can be independently varied to simulate different conditions.

Product Code : ELSHADDAI CHE - 005

LIQUID-LIQUID EXTRACTION IN A PACKED TOWER

The set-up consists of a glass column packed with Rasching rings. Continuous counter current contacts between the solvent and solute phases are made, which results into extract and raffinate streams. Flow meters (Rotameters) are used to note the flow of solvent & solute respectively.

Product Code : ELSHADDAI CHE - 007

FORCED DRAFT TRAY DRYER

The set-up consists of an insulated double wall chamber. Inside the chamber a tray is attached directly to a electronic weighing balance, which is fitted on the bottom, outside the chamber. Material for drying is placed in the tray and regular loss of weight is monitored. Air from a blower passes through a heating chamber and is used as drying agent.

Product Code : ELSHADDAI CHE - 009

Steam Distillation

Steam distillation is used industrially to purify liquids, which are immiscible with water, and to remove bad odors from oils. When water is added to a high boiling liquid immiscible with it, the total pressure exerted by the mixture above the liquid surface will be the sum of the vapor pressures of the pure components and therefore the boiling point of the mixture will be less than that of water at the given temperature.

Product Code : ELSHADDAI CHE - 011

Jaw Crusher

The set-up contains two Jaws of hard steel with one Jaw stationary and other moving. The movable jaw produces blows for every revolution reducing over sizing to a minimum. A combination of forward and downward strokes with a rocking action exert pressure on the coarser materials yet permits the finished materials to pass through the jaws. A hopper is provided at the top for feeding material. The smooth jaws ensure a uniform product and easy cleaning is possible

Product Code : ELSHADDAI MECH - 012

ROLL CRUSHER

Lab setup is used to crush different sample and material. Two heavy smooth faced chilled metal rolls turning on parallel horizontal axes are the working elements of the roll crusher. A hopper is provided at the top for feeding the material. Particles of feed caught between the rolls are broken in compression and drop out below. The rolls turn towards each other at the same speed.

Product Code : ELSHADDAI MECH - 014

PRESSURE DROP THROUGH PACKED BED

We offer high quality Michell Tilting Pad Bearing Apparatus to our esteemed customers. The offered apparatus is commonly used for the purpose of demonstrating the pressure distribution that occurs in pad bearing. Owing to easy the installation and flawless design, this offered apparatus is highly demanded in the market.

Product Code : ELSHADDAI MTL - 015

FLOW THROUGH HELICAL COIL

Helical coils are used for heating or cooling in process tanks. When a fluid flows through a curved tube, centrifugal force acting upon the various elements of fluid moving with different velocities causes secondary circulation. Secondary flow results in higher heat transfer characteristics. Further, secondary flow stabilizes the laminar flow leading to a higher critical Reynolds number for transition from laminar to turbulent flow.

Product Code : ELSHADDAI MTL - 017

PRESSURE DROP IN TWO PHASE FLOW

 Water Circulation FHP Pump, Crompton / Sharp make

 Flow Measurement Rotameters. 2 Nos. (one each for Water & Air).

 Air Circulation By Compressed Air

 Water Tank Material Stainless Steel/PVC, Capacity 60 Ltrs

Product Code : ELSHADDAI MTL - 019

Refrigerator Test Rig

To determine the COP of given plant. The apparatus consists of a compressor, condenser, dryer, digital temperature indicator, sensor, pressure gauge & vacuum gauge. Eco-friendly R 134A is used as refrigerants in our Air Conditioning Test Rig. Our Air Conditioning Test Rig is highly useful in conducting experiments on a vapor compression air conditioning unit.

Product Code : ELSHADDAI R/AC - 001

FLUIDIZED BED COOLING TOWER

 Size : 250 x 250 mm

 Height : 1000 mm

 Material : Aluminum body with acrylic frame

 Geyser : Capacity: 3KW

Product Code : ELSHADDAI R/AC - 003

Ice Plant Test Rig

The Ice Plant Test rig works on simple compression refrigeration cycle and uses R134-a or R404-A as a refrigerant. These are environment friendly. It is also useful to understand working of vapour compression system, its performance and controls used. The arrangement of parts such that, all the parts are visible and working can be easily understood

Product Code : ELSHADDAI R/AC - 005

VORTEX TUBE TEST RIG

The Vortex Tube Test Rig is one of the non- conventional methods of cooling which has no moving parts. It requires only source of compressed air. Through this tube, when air is admitted at high pressure, from one end, hot sir is discharged and from the other end, cold air comes out. The test rig is designed such that all the performance can be evaluated.

Product Code : ELSHADDAI R/AC - 007

Water Cooler Test Rig

 Compressor : Hermetically sealed compressor having cooling capacity of (as per water cooler)

 Condenser : Air cooled condenser made up of copper pipe & Aluminum fins

 Thermostat : 5 degree C to 15 degree C

 Voltmeter : 0-300 V

Product Code : ELSHADDAI R/AC - 009

COOLING TOWER TEST RIG

 Size : 250 x 250 mm

 Height : 1000 mm

 Material : Aluminum body with acrylic frame

 Geyser : Capacity: 3KW

Product Code : ELSHADDAI R/AC - 011

split a/c test rig

 Size : 250 x 250 mm

 Height : 1000 mm

 Material : Aluminum body with acrylic frame

 Geyser : Capacity: 3KW

Product Code : ELSHADDAI R/AC - 011

UNIVERSAL TESTING MACHINE 40 TON

“Elshaddai’s” Universal Testing Machine which is available in electronic and computerized functioning. This machine is used to test the tensile and compressive properties of material. The reason Universal Testing machine is named so because it can perform all the tests right from compression, bending to tension and examine the material in all mechanical properties. We offer these in grade of 10T, 20T, 40T, 60T and 100T.

Product Code : ELSHADDAI SOM - 001

ERICHSEN CUPPING TESTING MACHINE

“Elshaddai’s” This is designed to reveal the cupping qualities of metal sheets & strips and also to test the adhesion, elasticity & porosity of coasts of plants or varnish by way of comparison. The appearance of material & also of its constitution to some extent.

Product Code : ELSHADDAI SOM - 003

COMPRESSION TESTING MACHINE

“Elshaddai’s” Conforming to the specifications and tolerance in accordance to I.S.-516 for the determination of the compressive strength on cube moulds, manually operated with hardened platens and pressure gauge range 1000 KN capacity calibrated against N.P.L.Tested Proving ring or master gauge.

Product Code : ELSHADDAI SOM - 005

SPRING TESTING MACHINE

“Elshaddai’s” It is used for testing springs under Tension & Compression Loads. Different Capacities from 100 Kg upto 100 Ton are manufactured. Different Models Like Manually Operated, Electrically Operated, Electronic (Digital) & Computerized Models are manufactured as per clients requirement.

Product Code : ELSHADDAI SOM - 007

VICKER’S TESTING MACHINE

“Elshaddai’s” Vickers Hardness Tester is a simple and accurate means to produce and measure the diamond indentation.

Product Code : ELSHADDAI SOM - 009

HARDNESS TESTING MACHINE

“Elshaddai’s” We manufacture Rockwell hardness testers & Rockwell Cum Brinell hardness testers that are used for measuring hardness of all kinds of alloys and metals, whether hard or soft, round or flat or irregular in shapes. These machines are as per IS:1586- 2000 standards and are also available in motorized versions. Such products find their applications in tool rooms, laboratories, Heat treatment shops, inspection departments, research & development departments, educational institutions and foundries.

Product Code : ELSHADDAI SOM - 011

Foil Strain Gauge

 Gage Length : 0.3mm to 60mm

 Gage Resistance : Within 0.3 %of the nominal resistance

 Foil Material : Cu-Ni Alloy

 Base Material : Polyimide

Product Code : ELSHADDAI STR - 001

Demountable Mechanical Strain Gauge

This portable gauge is designed for a gauge length of 20c.m of the reference pins. The deformation isindicated by a 0.002 x 10mm dial gauge attached to the instruments

Product Code : ELSHADDAI STR - 003

Sieves

Conforming to the specifications and tolerance in accordance to I.S. 460 for fine materials made out of 20cms. Diam spun type joint less polished brass frame easily fit on each other equipped with stainless-steel wire mesh aperture size

Product Code : ELSHADDAI CVL - 029

Softening Point Apparatus Ring

Conforming to the specifications and tolerance in accordance to I.S.2720 part-v and latest I.S.9259.Consists of a hard rubber base carrying a sliding carriage assembly to which a brass cup is hinged. The cup is raised and allowed to fall through a height of 1cm by the help of a lead screw provided at the back of the sliding carriage.

Product Code : ELSHADDAI CVL - 031

SHINKAGE LIMIT APPARATUS

Conforming to the tolerance and specifications in accordance to I.S.2720 part-vii, for the determination of the water content level after which any further reduction in the water content will not cause a corresponding decrease in the volume of the soil mass.

Product Code : ELSHADDAI CVL - 033

DIRECT SHEAR APPARATUS

Conforming to the Specifications and tolerance in accordance to I.S.-2720 Part-XXVIII consists of :- Small sand pouring cylinder 3 liter capacity mounted above a pouring cone and separated as a shutter hole. Cylindrical Calibrating container internal diam 100mm and internal depth 150mm fitted with a flendge 5 cm. wide. Metal Tray 30cms square and 4 cms. Deep with a 10cms. Hole in the centre.

Product Code : ELSHADDAI CVL - 035

TRIAXIAL SHEAR APPARATUS

Conforming to the Specifications and tolerance in accordance to I.S.-2720 Part-XXVIII consists of :- Small sand pouring cylinder 3 liter capacity mounted above a pouring cone and separated as a shutter hole. Cylindrical Calibrating container internal diam 100mm and internal depth 150mm fitted with a flendge 5 cm. wide. Metal Tray 30cms square and 4 cms. Deep with a 10cms. Hole in the centre.

Product Code : ELSHADDAI CVL - 037

Soil Permeability Apparatus

Conforming to the Specifications and tolerance in accordance to I.S.-2720 Part-XXVIII consists of :- Small sand pouring cylinder 3 liter capacity mounted above a pouring cone and separated as a shutter hole. Cylindrical Calibrating container internal diam 100mm and internal depth 150mm fitted with a flendge 5 cm. wide. Metal Tray 30cms square and 4 cms. Deep with a 10cms. Hole in the centre.

Product Code : ELSHADDAI CVL - 039

TILE FLEXURAL TESTING MACHINE

Unit for finding flexural strength of clay roofing tiles and cement concrete flooring tiles. Flexural load is applies on the tiles using lead shots. The machine consists of a stand on which two 40mm dia bearing rollers or 12mm dia rollers are placed at centre distance of 150mm, 200mm, 250mm, or 270mm as the case may be. The third upper roller applies centrally flexural load by means of lever arrangement

Product Code : ELSHADDAI CVL - 041

Vernier Transit Theodolite

Accuracy : 20 sec

Magnification : 20x

Standard deviation : 20’’ (direction deviation 5mm at 100m

Product Code : ELSHADDAI CVL - 040

TOTAL STATION

Total stations are mainly used by land surveyors and civil engineers, either to record features as in topographic surveying or to set out features and it is a surveying equipment combination of Electromagnetic Distance Measuring Instrument and electronic theodolite.

Product Code : ELSHADDAI CVL - 042

ABNEY LEVEL

Survey Equipments - Survey Equipments suppliers, Survey Equipments producers, Survey Equipments exporters from India - Survey Equipment - Survey Instruments

Product Code : ELSHADDAI CVL - 044

TROUGH COMPASS

Survey Equipments - Survey Equipments suppliers, Survey Equipments producers, Survey Equipments exporters from India - Survey Equipment - Survey Instruments

Product Code : ELSHADDAI CVL - 046

SURVEY PLANE TABLE

Survey Equipments - Survey Equipments suppliers, Survey Equipments producers, Survey Equipments exporters from India - Survey Equipment - Survey Instruments

Product Code : ELSHADDAI CVL - 048

PRISMATIC COMPASS

Survey Equipments - Survey Equipments suppliers, Survey Equipments producers, Survey Equipments exporters from India - Survey Equipment - Survey Instruments

Product Code : ELSHADDAI CVL - 050

BRASS PANTAGRAPH

Survey Equipments - Survey Equipments suppliers, Survey Equipments producers, Survey Equipments exporters from India - Survey Equipment - Survey Instruments

Product Code : ELSHADDAI CVL - 052

MEASURING WHEEL

Survey Equipments - Survey Equipments suppliers, Survey Equipments producers, Survey Equipments exporters from India - Survey Equipment - Survey Instruments

Product Code : ELSHADDAI CVL - 054

Ranging Rod

Survey Equipments - Survey Equipments suppliers, Survey Equipments producers, Survey Equipments exporters from India - Survey Equipment - Survey Instruments

Product Code : ELSHADDAI CVL - 056

Aluminium Leveling Staff

Survey Equipments - Survey Equipments suppliers, Survey Equipments producers, Survey Equipments exporters from India - Survey Equipment - Survey Instruments

Product Code : ELSHADDAI CVL - 058

Three wheeler chassis

These products are specially designed by our engineers to improve two and three wheeler design knowledge and troubleshooting technique to the students.

Product Code : ELSHADDAI AUTO - 001

Coil spring Test Rig

It Consists of Column Frame, Pneumatic Cylinder, FRL, Double Acting Solenoid Valve, Load Measuring Sensor, Displacement Measuring Sensor, etc,. It used to test the all type of Compression Coil Spring in Two & Three Wheeler.

Product Code : ELSHADDAI AUTO - 003

Fuel Injection Pump calibration test bench

 Single phase & Three phase as per requirement

 3000 variable rpm speed with digital meter

 Digital strok counter for measure fuel quantity

 Suteble for all type of fuel injection pump & common rail testing

Product Code : ELSHADDAI AUTO - 005

Valve Re-facing machine

We are suppliers of Valve Grinding Machine. By using this machine we can perform grinding process for engine valve seat area.

Product Code : ELSHADDAI AUTO - 007

3D Wheel Alignment Machine

We are from Elshadai Engineering Equipments; we do have the wide range of 3D wheel Alighment Machine. Our measuring sensors attach directly to the object we are measuring (vehicle wheel). The 3D alignment system takes an image of a target mounted to the wheel and uses software to determine the wheel position.

Car Wheel Balancing Machine

We are supplying Car Wheel Balancing Machine in several stipulations

Car Nitrogen Tyre Inflator

Engineering Students Drafting Table

ELSHADDAI is one of the primary sources for drafting supplies and drawing equipment

Product Code : ELSHADDAI ARCH - 001

Digital Weather Station with Forecast

Indoor Temperature Range : 32 to 122 degrees Fahrenheit; 0 to 50 degrees Celsius

Temperature Accuracy : +/- 2 degrees Fahrenheit

Product Code : ELSHADDAI ARCH - 003

Solarimeter

Solarmeter UVB Meter For Reptile Lamps - Measures 280-320nm with range from 0-1999 µW/cm² Total UVB

Product Code : ELSHADDAI ARCH - 005

Drawing Instruments Box

ELSHADDAI is one of the primary sources for drafting supplies and drawing instruments

Product Code : ELSHADDAI ARCH - 007

Mini Drafter

 Metal body with steel rad

 Expended size 60cm scale size 15cm x 25 cm

 Fiber material with Zero % error & angle measurement

 Light weight

Product Code : ELSHADDAI ARCH - 009

Wind Tunnel

This is an open circuit Wind Tunnel which provides a region of controlled airflow into which models can be inserted. The propulsion is provided by a fan at downstream of working section. The tunnel consists of bell mouth shaped entry to guide the air smoothly into settling chamber consisting of honeycomb and nylon mesh screens which filters and stabilizes the air flow. This follows working section or test section where various models can be tested.

Product Code : ELSHADDAI AE - 001

Beam Test Setup

A bench mounted beam apparatus to allow students to investigate the deflections and reactions in simply supported and cantilevered beams

Product Code : ELSHADDAI AE - 003

Propeller Test Rig

In this test rig, performance of a Propeller can be investigated. The propeller is mounted on a shaft of DC motor. The load cell arrangement is used to measure the thrust force produced by the propeller.

Product Code : ELSHADDAI AE - 005

Flow Visualization Apparatus

The unit uses water as the flow medium. A contrast medium (dye) is injected through small needles into the flow area. Various drag bodies (included) can be placed in the area of flow. In addition, sources and sinks can be simulated and illustrated using eight additional openings in the flow area.

Product Code : ELSHADDAI AE - 006

DOCTOR CENTRIFUGE

We make use of premium quality material and latest technology machines for the production of this doctor centrifuge by our industry senior most professionals.

Product Code : ELSHADDAI CVL - 028

Sand Muller

Sand Mixer/ Muller is fixed with adjustable solid wheels to give the required sand strength and compactness

Product Code : ELSHADDAI FST - 001

Sand Seiver

Sand Seiver is widely used to determine AFS (fineness no of sand)

 Motor 1/8 HP Single Phase

 Sieve Set as per ISS No.53,75,106,150,212,300,425, 600,850,1700

 Microns Dia. Of Sieve 200 mm,

Product Code : ELSHADDAI FST - 003

SAND WASHER

 It is use to find out clay % of raw sand.

 Motor 1/20 HP Single Phase, cycles 50,

 Speed Regulator Timer, Glass jar, Syphon

Product Code : ELSHADDAI FST - 005

Core Permeability

We are the leading foundry sand testing equipment suppliers in Chennai offering multiple lab testing equipments like Sand Rammer, Permeability Tester and Permeability Tester Electric at reasonable cost. Our Foundry Sand Testing Equipments are delivered to any part of India and 100% satisfaction guaranteed on ELSHADDAI ENGINEERING EQUIPMENTS.

Product Code : ELSHADDAI FST - 007

Liquid Limit

We are the leading foundry sand testing equipment suppliers in Chennai offering multiple lab testing equipments like Sand Rammer, Permeability Tester and Permeability Tester Electric at reasonable cost. Our Foundry Sand Testing Equipments are delivered to any part of India and 100% satisfaction guaranteed on ELSHADDAI ENGINEERING EQUIPMENTS.

Product Code : ELSHADDAI FST - 009

Mould Hardness Tester

We are the leading foundry sand testing equipment suppliers in Chennai offering multiple lab testing equipments like Sand Rammer, Permeability Tester and Permeability Tester Electric at reasonable cost. Our Foundry Sand Testing Equipments are delivered to any part of India and 100% satisfaction guaranteed on ELSHADDAI ENGINEERING EQUIPMENTS.

Product Code : ELSHADDAI FST - 011

Transverse Strength Machine

We are the leading foundry sand testing equipment suppliers in Chennai offering multiple lab testing equipments like Sand Rammer, Permeability Tester and Permeability Tester Electric at reasonable cost. Our Foundry Sand Testing Equipments are delivered to any part of India and 100% satisfaction guaranteed on ELSHADDAI ENGINEERING EQUIPMENTS.

Product Code : ELSHADDAI FST - 013

Flowability Tester

We are the leading foundry sand testing equipment suppliers in Chennai offering multiple lab testing equipments like Sand Rammer, Permeability Tester and Permeability Tester Electric at reasonable cost. Our Foundry Sand Testing Equipments are delivered to any part of India and 100% satisfaction guaranteed on ELSHADDAI ENGINEERING EQUIPMENTS.

Product Code : ELSHADDAI FST - 015

AXIAL FLOW COMPRESSOR TEST RIG (3 STAGES). (BASIC MODEL) (PROPULSION- LAB)

In an axial-flow compressor, air passes from one stage to the next with each ... and the second set of combustors are located between the high-pressure and the ... a blade element showing wm, the appropriate velocity upon which to base the lift ... model will not be accurate and careful consideration of the three-dimensional

BOYS GAS CALORIMETER (For LPG and liquid fuel) (PROPULSION- LAB)

Introduction Boy's gas calorimeter was designed to get accurate values of the higher and lower calorific value of given fuel. Mainly we can measure the calorific value of gaseous fuels only because the practical apparatus was designed for that purpose.

RADIAL 14 CYLINDER PISTON ENGINE (PROPULSION- LAB) (PROPULSION- LAB)

The radial engine is a reciprocating type internal combustion engine configuration in which the cylinders point outward from a central crankshaft like the spokes of a wheel. It resembles a stylized star when viewed from the front, and is called a "star engine" (German Sternmotor) in some languages. The radial configuration was very commonly used in aircraft engines before turbine engines became predominant.

DUCT BURNER TESTRIG(PROPULSION- LAB)

Duct burners are designed to work inside heat-recovery steam generator (HRSG) in order to increase the heat energy of a gas turbine exhaust. Duct burners guarantee maximum flame stability and reliability providing low emissions on a wide variety of applications.

Duct Burners to resist to the high temperature inside the duct and to provide long equipment life for components since they are used in combined cycles and they can work either with fresh air (when gas turbine is turned off) or exhaust gas. These burners are usually provided in multiple row and they are designed in modular configuration for an easy construction and maintenance.

BLOWER BALANCE AND SMALL ASPECT RATIO (PROPULSION- LAB)

The Blower is coupled to an induction motor of 3HP. The Blower is coupled with a Dynamometer type motor with a stepped pulley arrangement to run at three different speeds, balance arm, dial type spring balance with a large size dial etc., to determine the input power of the blower. Instrumentation.

RAMJET ENGINE (PROPULSION- LAB)

A jet engine that consists essentially of a hollow tube without mechanical components and depends on the aircraft's speed of flight to compress the air which is supplied to a burner from which hot gases are discharged rearward Ramjet Engine Diffuse Diameter:0.036m Overall Length :0.650 M Thickness:0.0016m Nozzle Angle :16 Degree Material:Heat Resistant Alloy Steel (Stainless Steel) Fuel Used:Gasoline Fuel Delco Motor Unit Connected With Magneto Ignition Fuel

Apparatus for Verification Of Clarke's Maxwell Theorem

Apparatus consist of a mild steel beam 100cm long and 1.25cm X 4mm in cross section with graduations at every 10cm along the length. It should be supported on two knife edge supports 70cm apart with a 30cm overhang on one side. Reciprocal theorem can be verified by direct measurements of the deflections of various points with the help of a dial gauge due to a load placed at the reciprocal points.

Product Code : ELSHADDAI AM - 001

Curved Member Apparatus

Apparatus consists of a steel bar which is used to make the different curved member Viz. circle, semicircle with straight arm, a quadrant of a circle and quadrant of a circle with straight arm. The bottom ends of the members are fixed to the base. Under the application of load at free end, its horizontal and vertical deflection can be measured with the help of dial gauges.

Product Code : ELSHADDAI AM - 003

Elastic Properties of Deflected Beam Apparatus

Apparatus consists of a mild steel beam 2.5cm X 3mm in cross section and 100cm long, pinned to two supports 70cm apart situated symmetrically. One of the ends can be fixed or given a known slope by applying a known moment at the end with the help of suspended loads. At the other end also a known moment can be applied. Vertical loads can be applied at various points along the span of the beam. A Dial gauge with 25mm travel ( with a magnetic base) may be supplied with the apparatus.

Product Code : ELSHADDAI AM - 005

Portal Frame Apparatus

Apparatus made up of M.S. plate of rectangular section of 3mm thick X 40cm wide. Frame is provided with a provision to achieve different end conditions viz. hinged, roller & fixed. The size of portal will be 40cm X 60 cm. Portal may also have a provision for pulley arrangement and hook arrangement for horizontal loading at different positions. A dial gauge with 25mm travel (with a magnetic base) is supplied with the apparatus. Apparatus will be supplied complete with a supporting stand and a set of weights.

Product Code : ELSHADDAI AM - 007

Unsymmetrical Bending Apparatus

Apparatus consists of a mild steel angle of size 1" X 1" X 1/8" or an equivalent metric units of length 80 cm is tied as a cantilever beam. The beam should be fixed at one end such that the rotation of 45degree intervals are given and clamped such that the principal axis of its cross-section may be inclined at any angle with the horizontal and vertical planes. Also arrangement will be provided to apply vertical load at the free end of the cantilever and to measure horizontal and vertical deflection of the free end.

Product Code : ELSHADDAI AM - 009

Parallelogram Law Of Forces Apparatus

This item is similar to the wall type but is intended for use in laboratories where wall space is limited. At thick plywood piece of thickness 12 mm having substantial metal stand with 2 set of z-pulley and 3 set of ( 50 x 5 gm) slotted weights.

Product Code : ELSHADDAI AM - 011

PRONY BRAKE DYNAMO METER

Consisting of a two blocks of wood clamped together with pulley in the center. The pulley is fitted to shaft moving on the ball bearings. Al lever bar is attached to one of the two blocks carrying a weight hanger at the outer end. A spring balance is also fitted to measure the load factor developed with tightening of the block with wing nut & spring.

Product Code : ELSHADDAI AM - 013

Oven

The set-up contains two Jaws of hard steel with one Jaw stationary and other moving. The movable jaw produces blows for every revolution reducing over sizing to a minimum. A combination of forward and downward strokes with a rocking action exert pressure on the coarser materials yet permits the finished materials to pass through the jaws. A hopper is provided at the top for feeding material. The smooth jaws ensure a uniform product and easy cleaning is possible

Product Code : ELSHADDAI CHE - 010

Digital Spectrophoto meter

Lab setup is used to crush different sample and material. Two heavy smooth faced chilled metal rolls turning on parallel horizontal axes are the working elements of the roll crusher. A hopper is provided at the top for feeding the material. Particles of feed caught between the rolls are broken in compression and drop out below. The rolls turn towards each other at the same speed.

Product Code : ELSHADDAI CHE - 012

Auto Karl Fischer Titrimeter

Lab setup is used to crush different sample and material. Two heavy smooth faced chilled metal rolls turning on parallel horizontal axes are the working elements of the roll crusher. A hopper is provided at the top for feeding the material. Particles of feed caught between the rolls are broken in compression and drop out below. The rolls turn towards each other at the same speed.

Product Code : ELSHADDAI CHE - 014

Isothermal Continuously Stirred Tank Reactor

The set up consists of two overhead feed tanks through which two reactants are fed to the reactor. Rotameters are provided to measure the individual flow of Chemicals. The flow rate can be adjusted by operating the needle valves provided on respective Rotameter

Product Code : ELSHADDAI CHE - 001

PLUG FLOW TUBULAR REACTOR

The set up consists of two feed tanks through which two reactants are fed to the reactor. Rotameters are provided to measure the individual flow of Chemicals. The flow rate can be adjusted by operating the needle valves provided on respective Rotameter. The compressed air is used for circulation of feed. A straight tube type reactor kept horizontally and inclined upward at outlet from where samples are collected for analysis. Pressure Regulator, Pressure Gauge and Safety Valve are fitted in the compressed air line

Product Code : ELSHADDAI CHE - 003

Plug Flow Reactor

This Set-Up Is Used To Study A Non-Catalytic Homogeneous Reaction Under Isothermal Condition. The Set Up Consists Of Two Feed Tanks Through Which Two Reactants Are Fed To The Reactor. Rotameters Are Provided To Measure The Individual Flow Of Chemicals. The Flow Rate Can Be Adjusted By Operating The Needle Valves Provided On Respective Rotameter. The Compressed Air Is Used For Circulation Of Feed. It Is A Helical Coil Tube Type Reactor Kept In A Constant Temperature Water Bath To Conduct The Experiment At Various Temperatures. Reactants Enter At Lower End Coming Out Of The Top Of Coil From Where Samples Are Collected For Analysis. Pressure Regulator, Pressure Gauge And Safety Valve Are Fitted In The Compressed Air Line.

Product Code : ELSHADDAI CHE - 003

CUBE MOULDS

Made of cast iron conforming to the specifications and tolerance in accordance to I.S.-516 and latest I.S.-10074 SIZE- 150 X 150X150MM.

Product Code : ELSHADDAI CVL - 001

PRISM MOULD

One gang prism mould to produce 25x25x250 mm specimens for expansion tests in autoclave. Complete with 4 steel inserts.

Product Code : ELSHADDAI CVL - 003

CONCRETE MIXER

Laboratory model capacity 2.5 cft mounted on rubber tiers and sturdy frame with towing rod. ELECTRICALLY OPERATED.

Product Code : ELSHADDAI CVL - 005

FLOW TABLE

Conforming to the specification and tolerance in accordance to I.S.-1199. Designed for the determination of the flow of the Portland cement concrete. The tabletop is 76.2cms. Diam finally machined from a solid casting the integral cast ribs are also designed for support and strength. The stand is fabricated out of cast iron and is on sturdy construction. Holes for mounting on foundation are drilled in the base plate. The ground and polished steel cam is designed to drop 12.5mm. Manually operated unit

Product Code : ELSHADDAI CVL - 007

VEE-BEE CONSISTOMETER

Conforming to the specifications and tolerance in accordance to I.S.-1199 used for the determination of the workability of the concrete. The concrete is deform in a container and is vibrated after removing the cone on a small vibrating table operated at a fixed amplitude and frequency operation 220 Volts single phase A.C.supply

Product Code : ELSHADDAI CVL - 009

LABORATORY C.B.R. APPARATUS (HAND OPERATED)

Conforming to the specifications and tolerance in accordance to I.S.-2720, Part-XVI used for the determination of the laboratory C.B.R. consists of : - 01.) Load Frame Hand operated capacity 50 KN (5000 kgs.) with high and low rate of travel of the lead screw. 02.).C.B.R. Mould:-Conforming to the specifications and tolerance in accordance to I.S.-9669-1980 made of chromium steel 150mm.

Product Code : ELSHADDAI CVL - 011

TROWELS AND PLANERS

Conforming to the specifications and tolerance in accordance to I.S.-2720, Part-XVI used for the determination of the laboratory C.B.R. consists of : - 01.) Load Frame Hand operated capacity 50 KN (5000 kgs.) with high and low rate of travel of the lead screw. 02.).C.B.R. Mould:-Conforming to the specifications and tolerance in accordance to I.S.-9669-1980 made of chromium steel 150mm.

Product Code : ELSHADDAI CVL - 013

MARSHALL STABILITY APPARATUS

The test is applicable to hot mix designs using bitumen and aggregates upto a maximum size of 25mm. In this method, the resistance to plastic deformation of cylindrical specimen of bitumenous mixture is measured when the same is loaded at periphery at 5 cm per min. This test procedure is used in designing and evaluating bitumenous paving mixes.

Product Code : ELSHADDAI CVL - 015

DORRY ABRASION TESTING MACHINE

Owing to our years of experience and knowledge of this domain, we have been able to manufacture, supply, export and trade finest quality Dorry Abrasion Testing Machine. We have manufactured the offered range of abrasion testing machines using high grade raw material and components that are obtained from the most trusted and reputed vendors of the market. Offered Dorry Abrasion Testing Machine is generally used to test the coarse aggregate abrasion resistance.

Product Code : ELSHADDAI CVL - 017

two stroke diesel engine

This working cut section model designed to enable students to study different systems of an automobile petrol and diesel engine & demonstrate its working. The setup uses an actual automobile petrol and diesel engine, sectioned at suitable locations to display internal assembles.

Product Code : ELSHADDAI CSW - 001

four stroke petrol engine

This working cut section model designed to enable students to study different systems of an automobile petrol and diesel engine & demonstrate its working. The setup uses an actual automobile petrol and diesel engine, sectioned at suitable locations to display internal assembles.

Product Code : ELSHADDAI CSW - 003

Model of Cut Sectioned Petrol MPFI Engine Assembly

This cutaway model is carefully sectioned for training purposes, professionally painted with different colours to better differentiate the various parts, cross-sections, lubricating circuits, fuel system, cooling system etc.

Product Code : ELSHADDAI CSW - 005

Engine Parts cut section

This cutaway model is carefully sectioned for training purposes, professionally painted with different colours to better differentiate the various parts, cross-sections, lubricating circuits, fuel system, cooling system etc.

Product Code : ELSHADDAI CSW - 007

Cut section of the brake Assembly

This cutaway model is carefully sectioned for training purposes, professionally painted with different colours to better differentiate the various parts, cross-sections, lubricating circuits, fuel system, cooling system etc.

Product Code : ELSHADDAI CSW - 009

CNC TURN TRAINER

 Table size : 400*150mm

 Tool Dia : 5/6/8mm

 Accuracy : 0.01mm

 Weight : 350 kgs

Product Code : ELSHADDAI CNC - 001

CAM ANALYSER

The apparatus is designed to study the cam profiles and performance of cam and follower system. A shaft supported by ball bearings upon which three different types of cams can be mounted.

Product Code : ELSHADDAI DYN - 001

GOVERNOR

To study the determination of characteristics curves of radius of rotation against controlling force (Actual & Theoretical) for all governors. The set-up is designed to study the working of different governors normally used to control the speed. It consists of a main spindle, mounted vertically on the base plate.

Product Code : ELSHADDAI DYN - 003

STATIC AND DYNAMIC BALANCING MACHINE

This equipment is designed for carrying out the experiment for balancing a rotation mass system. The apparatus consists of four circular discs mounted on a shaft. The discs are grooved for the attachment of weights at a specific radius. The block are clamped on shaft is rotated by a motor to check dynamic balance of the system.

Product Code : ELSHADDAI DYN - 005

VIBRATION TEST FACILITIES APPARATUS

The apparatus is designed to help in conducting various experiments to illustrate and verify the principles and relations involved in the study of vibrations. Following experiments can be performed with this unit.

Product Code : ELSHADDAI DYN - 007

DYNAMIC BALANCING MACHINE

Weight : 2-10kg,
Max. Distance Between Bearing: 500mm,
Balancing Speed Range (N)600-3000rpm,
Shaft Diameter5-50mm,
Power Of Drive Motor 0.33hp ,
Acceleration Capacity Gd2 N20.40x106 Kgm2n2,
Max. Unbalance Mass Read At 100% Of Meter Scale:30gm

Product Code : ELSHADDAI DYN - 009

JOURNAL BEARING APPARATUS

EEE Journal Bearing apparatus for investigating the distribution of pressure in slide bearings illustrates the principle of hydrodynamic lubrication. The distribution of pressure and the carrying capacity can be determined on a sliding bearing model at different bearing loads and speeds. The sliding bearing consists of a bearing journal driven by an electrical motor and the freely moving bearing housing. The bearing is loaded with different, interchangeable weights. The setup contains manometer tubes, dc motor, dc drive to control speed, set of weights, oil tank, Journal bearing along with the shaft.

Product Code : ELSHADDAI DYN - 011

BEVEL GEAR

Either of a pair of gears with teeth surfaces cut so that they can connect unparallel gear shafts. (Mechanical Engineering) a gear having teeth cut into a conical surface known as the pitch zone. Two such gears mesh together totransmit power between two shafts at an angle to each other

Product Code : ELSHADDAI DYN - 013

DIFFERENTIAL GEAR

An arrangement of gears in an epicyclic train permitting the rotation of two shafts at different speeds, used on the rear axle ofautomotive vehicles to allow different rates of wheel rotation on curves. An arrangement of gears in an epicyclic train permitting the rotation of two shafts at different speeds, used on the rear axle ofautomotive vehicles to allow different rates of wheel rotation on curves.

Product Code : ELSHADDAI DYN - 015

COMPOUND GEAR TRAIN

Compound gear trains involve several pairs of meshing gears. They are used where large speed changes are required or to get different outputs moving at different speed

Product Code : ELSHADDAI DYN - 017

Epicycle gear Train Apparatus

Gear Train is any combination of gear wheels by which motion is transmitted from one shaft to another shaft. In epicyclic gear trains, the axes of shafts on which the gears are mounted may move relative to a fixed axis.

Product Code : ELSHADDAI DYN - 019

ROPE BRAKE DYNAMOMETER

 230 V Single Phase
 Rope Brake Drum Assembly
 Digital R.P.M. Indicator
 Energy meter, Voltmeter, Ammeter to measure input power of motor

Product Code : ELSHADDAI DYN - 022

Slip & Creep Measurement Apparatus in Belt Drive

This apparatus is useful for measurement of power transmitted for various input power conditions with varied belt tension. Belt slip or creep also can be measured. The apparatus consists of a variable speed D.C. Motor, driving pulley and driven pulley of equal diameters. The pulleys are mounted on input shaft (motor shaft) and output shaft. The driven pulley can slide on the base only with bearing block to change the initial tension in belt

Product Code : ELSHADDAI DYN - 024

Drill Tool Dynamometer

Elshaddai’s Tool dynamometers to measure cutting forces on various machines like lathe, drill, milling machines. All three direction forces are measured simultaneously and displayed

Product Code : ELSHADDAI DYN - 026