Apparatus for Verification Of Clarke's Maxwell Theorem
Apparatus consist of a mild steel beam 100cm long and 1.25cm X 4mm in cross section with graduations at every 10cm along the length. It should be supported on two knife edge supports 70cm apart with a 30cm overhang on one side. Reciprocal theorem can be verified by direct measurements of the deflections of various points with the help of a dial gauge due to a load placed at the reciprocal points.
Product Code : ELSHADDAI AM - 001
Send A EnquiryBehaviour Of Column and Struts Apparatus
Apparatus consist of four spring steel columns which are put along a vertical wooden board. These four columns have different end conditions as below: 1. Both ends pinned 2. Both ends fixed 3. One end pinned and other fixed 4. One end fixed and other end free Apparatus will be supplied complete with a supporting stand and a set of weights.
Product Code : ELSHADDAI AM - 002
Send A Enquiry
Curved Member Apparatus
Apparatus consists of a steel bar which is used to make the different curved member Viz. circle, semicircle with straight arm, a quadrant of a circle and quadrant of a circle with straight arm. The bottom ends of the members are fixed to the base. Under the application of load at free end, its horizontal and vertical deflection can be measured with the help of dial gauges.
Product Code : ELSHADDAI AM - 003
Send A EnquiryElastically Coupled Beam Apparatus
Apparatus consists of a three parallel bar suspension system with elastic beam at their upper and lower ends. The upper ends of the two outer suspension rods are tied to a vertical wooden board while central suspension rod may be tied to the center of another elastic beam supported at two outer ends only. Apparatus to be supplied should be complete with a supporting stand and a set of weights.
Product Code : ELSHADDAI AM - 004
Send A Enquiry
Elastic Properties of Deflected Beam Apparatus
Apparatus consists of a mild steel beam 2.5cm X 3mm in cross section and 100cm long, pinned to two supports 70cm apart situated symmetrically. One of the ends can be fixed or given a known slope by applying a known moment at the end with the help of suspended loads. At the other end also a known moment can be applied. Vertical loads can be applied at various points along the span of the beam. A Dial gauge with 25mm travel ( with a magnetic base) may be supplied with the apparatus.
Product Code : ELSHADDAI AM - 005
Send A EnquirySuspension Bridge Apparatus
Apparatus consists of two mild steel cables 0.5cm diameter in cross section and 150cm long, pinned to two supports 90cm apart situated symmetrically. One of the ends can be converted to a roller by applying a known load at the end with the help of suspended pulley system. Vertical loads can be applied at various points along the span of the beam. A dial gauge with 25mm travel (with a magnetic base) will be supplied with the apparatus.
Product Code : ELSHADDAI AM - 006
Send A Enquiry
Portal Frame Apparatus
Apparatus made up of M.S. plate of rectangular section of 3mm thick X 40cm wide. Frame is provided with a provision to achieve different end conditions viz. hinged, roller & fixed. The size of portal will be 40cm X 60 cm. Portal may also have a provision for pulley arrangement and hook arrangement for horizontal loading at different positions. A dial gauge with 25mm travel (with a magnetic base) is supplied with the apparatus. Apparatus will be supplied complete with a supporting stand and a set of weights.
Product Code : ELSHADDAI AM - 007
Send A EnquiryRedundant Joint Apparatus
Apparatus consists of three suspension members (spring balances) of different stiffness which are jointed at a point to form the redundant joint. The upper end of the suspension members being tied in a position to a vertical wooden board. Arrangement is provided to apply a vertical load at the joint and to measure its horizontal and vertical displacement on a paper and also elongations and forces in the suspension members by the help of dial gauges. Two dial gauges with 25mm travel (with magnetic bases) are supplied with the apparatus.
Product Code : ELSHADDAI AM - 008
Send A Enquiry
Unsymmetrical Bending Apparatus
Apparatus consists of a mild steel angle of size 1" X 1" X 1/8" or an equivalent metric units of length 80 cm is tied as a cantilever beam. The beam should be fixed at one end such that the rotation of 45degree intervals are given and clamped such that the principal axis of its cross-section may be inclined at any angle with the horizontal and vertical planes. Also arrangement will be provided to apply vertical load at the free end of the cantilever and to measure horizontal and vertical deflection of the free end.
Product Code : ELSHADDAI AM - 009
Send A EnquiryTorsion of Rods Apparatus
Low cost effective teaching
Self contained
Bench mounted
Product Code : ELSHADDAI AM - 010
Send A Enquiry
Parallelogram Law Of Forces Apparatus
This item is similar to the wall type but is intended for use in laboratories where wall space is limited. At thick plywood piece of thickness 12 mm having substantial metal stand with 2 set of z-pulley and 3 set of ( 50 x 5 gm) slotted weights.
Product Code : ELSHADDAI AM - 011
Send A EnquirySCREW JACK
All metallic construction accurately machine cut screw with a pitch of 5 mm carrying double flanged turned table of about 20 cm dia. Fitted on a heavy cast iron base and complete with two adjustable pulleys, cord & hooks without weights.
Product Code : ELSHADDAI AM - 012
Send A Enquiry
PRONY BRAKE DYNAMO METER
Consisting of a two blocks of wood clamped together with pulley in the center. The pulley is fitted to shaft moving on the ball bearings. Al lever bar is attached to one of the two blocks carrying a weight hanger at the outer end. A spring balance is also fitted to measure the load factor developed with tightening of the block with wing nut & spring.
Product Code : ELSHADDAI AM - 013
Send A EnquiryUNIVERSAL FORCE TABLE
It consists of cast aluminum plate of 400 mm dia. graduated in 360 degrees. The table is fitted on a case iron stable base with leveling screws to make the table in leveled position. It is possible to fix the table in any desired position. Supplied will six set of brass nickeled slotted weight each set containing nine weights and one hanger of 50 grams. And is complete with six sliding clamping pulleys to fix up the same.
Product Code : ELSHADDAI AM - 014
Send A Enquiry
