Leaf Filter - ELSHADDAI –
MOL – 001
Manufacturer, Supplier, and Exporter of Science Instruments by ELSHADDAI ENGINEERING EQUIPMENTS
The shell is a cylindrical tank the set-up consists of flat filtering elements (leaves) supported in a slurry tank. A filter leaf consists of a perforated plate over which a filter medium of woven fabric is fitted. The whole assembly is connected to a vacuum pump through a filtrate receiver. An agitator is fitted in the slurry tank. The drain valve is provided in it. The set-up is operated batch wise.
Plate And Frame Filter Press- ELSHADDAI –
MOL – 002
Manufacturer, Supplier, and Exporter of Science Instruments by ELSHADDAI ENGINEERING EQUIPMENTS
A filter press contains a set of plates designed to provide a series of chambers or compartments in which solids may collect. The plates are covered with a filter medium such as canvas cloth. Slurry is admitted to each compartment under pressure; passes through the canvas cloth and out a discharge pipe, leaving a wet cake of solids behind. Plates and frames sit horizontally in a metal rack, with cloth covering the face of each plate, and are squeezed tightly together by a screw. Slurry enters at one end of the assembly of plates and frame. It passes through a channel running lengthwise through one corner of assembly. The set up consists of 7 plates and 6 frames. Frames are covered with filter cloth. Feed is fed by gear pump at the top and filtrate collected at the bottom from each plate by operating the cock. After removing cake, washing and cleaning can be done by water provided by overhead tank. Inlet & outlet pressures are measured by pressure gauges. Rate of filtrate removals is measured by calibrated tank provided.
Sedimentation Jar - ELSHADDAI –
MOL – 003
Manufacturer, Supplier, and Exporter of Science Instruments by ELSHADDAI ENGINEERING EQUIPMENTS
The present set-up with 5 Nos. of Borosilicate Glass Graduated Cylinders is designed to study the zone settling depending upon the concentration and characteristics of the particles. These cylinders can be easily removed for cleaning. Rate of change in height of the various liquids/solids interfaces with respect to time can be measured with the help of stop watch.
Jaw Crusher - ELSHADDAI –
MOL – 004
Manufacturer, Supplier, and Exporter of Science Instruments by ELSHADDAI ENGINEERING EQUIPMENTS
Two Jaws of manganese steel are provided in this laboratory Jaw Crusher. The moveable Jaw produces two blows for every revolution, thus reducing over sizing to a minimum. A combination of forwarding and downward strokes with a rocking action exerts pressure on the coarser material, yet permits the finished material to pass through the Jaws. A hopper is provided at the top for feeding material
Ball Mill - ELSHADDAI –
MOL – 005
Manufacturer, Supplier, and Exporter of Science Instruments by ELSHADDAI ENGINEERING EQUIPMENTS
Ball Mills are horizontal rotating cylindrical steel chamber of half filled with steel balls. The size reduction is accomplished by the impact of balls as they fall back after being lifted by the baffles fitted in the rotating chamber. Ball Mill is fitted on a sturdy MS frame. Charging of balls and material is done by the means of opening provided in the chamber. The chamber is turning about the horizontal axis through a reduction gearbox drive through a ½ HP variable speed motor. Drive is provided to vary the RPM. A RPM indicator with proximity switch is provided in the set-up. A revolution counter is provided to find out the number of turns. Special arrangement is done to free the Ball Mill from reduction gearbox for charging and discharging the material.
Pulverizer - ELSHADDAI –
MOL – 006
Manufacturer, Supplier, and Exporter of Science Instruments by ELSHADDAI ENGINEERING EQUIPMENTS
The laboratory pulverizer is a disc type grinder, Designned to grind virtually any material to produce a fine mesh sample in one operation. The instrument is useful for assaying, mining and for metallurgical, quarrying, aggregate processing, chemical, geological and industrial laboratories. It is a self contained grinder, with a rotary disc, having a planetary movement in a vertical plane
Hammer Mill - ELSHADDAI –
MOL – 007
Manufacturer, Supplier, and Exporter of Science Instruments by ELSHADDAI ENGINEERING EQUIPMENTS
Hammer Mill Housing: Material Stainless Steel. Dia 145mm,
Depth : 75mm
Feed size: 6mm approx
Product size: (60 – 150) mesh approx
Hammers: Material stainless steel, 4 Nos. Size55mm x 15mm
Cyclone Separator - ELSHADDAI –
MOL – 008
Manufacturer, Supplier, and Exporter of Science Instruments by ELSHADDAI ENGINEERING EQUIPMENTS
A cyclone separator is a vertical cylinder with the inlet stream introduced tangentially near the top, giving the suspension a spinning rotation in the cylinder. The centrifugal force acting on the particles tends to throw them radically to the sides of the cylinder as they spiral downward to a conical bottom where they are removed. A collector is fitted at the bottom & the induced draft blower is used to create the air stream. The classified air leaves the cyclone through a pipe extended down into the cyclone & passes through blower delivery side fitted with fine screen cloth bag to avoid dust expansion in the laboratory. The setup consists of i.d. Blower connected to discharge side of cyclone separator. A flow meter with manometer is provided to measure the flow rate of air. Pressure drop in the cyclone is measured by water manometer. Solids are collected in the collector fixed at the bottom. The set-up is complete with flow control & by-pass valve.
Roll Crusher - ELSHADDAI –
MOL – 009
Manufacturer, Supplier, and Exporter of Science Instruments by ELSHADDAI ENGINEERING EQUIPMENTS
An Elutriator is vertical tube through which a fluid passes upwardly at a specific velocity while a solid mixture, whose separation is desired, is fed into the top of the column. The large particles, which settle at a velocity higher than that of the rising fluid, are collected at the bottom of the column, and the smaller particles are carried out of the top of the column with the fluid. Several columns of different diameters in series may be used to bring about a further separation. The set up consists of two vertical tubes of different diameter in which water is passed at a controlled velocity. A tank with pump is provided for re-cycled water supply and flow rate is measured by Rota meter and controlled with the help of control valve.
Elutriator Apparatus - ELSHADDAI –
MOL – 010
Manufacturer, Supplier, and Exporter of Science Instruments by ELSHADDAI ENGINEERING EQUIPMENTS
An Elutriator is vertical tube through which a fluid passes upwardly at a specific velocity while a solid mixture, whose separation is desired, is fed into the top of the column. The large particles, which settle at a velocity higher than that of the rising fluid, are collected at the bottom of the column, and the smaller particles are carried out of the top of the column with the fluid. Several columns of different diameters in series may be used to bring about a further separation. The set up consists of two vertical tubes of different diameter in which water is passed at a controlled velocity. A tank with pump is provided for re-cycled water supply and flow rate is measured by Rota meter and controlled with the help of control valve.
Drop Weight Crusher - ELSHADDAI –
MOL – 011
Manufacturer, Supplier, and Exporter of Science Instruments by ELSHADDAI ENGINEERING EQUIPMENTS
This setup is used to determine the crushing law of constants using drop weight crusher.
About 25 grams of the sample size 4+5 is taken in the crushing chamber. The weight of the metallic block (weight to be dropped) and the height through which it falls is determined.
Burr Mill- ELSHADDAI –
MOL – 012
Manufacturer, Supplier, and Exporter of Science Instruments by ELSHADDAI ENGINEERING EQUIPMENTS
Stainless Steel Body Light Weight Automatic Clean
Grinding Capacity: 6 Kg to 10 Kg. One Hour
Power: 230V, 50hz Single Phase.